Cable Drivers
- Silicon Motion Usb Devices Driver Download For Windows 10 64-bit
- Silicon Motion Usb Devices Driver Download For Windows 10 Windows 7
- Silicon Motion Usb Devices Driver Download For Windows 10 Offline
MD-CC3/4 and Windows x64 systems
Silicon Motion Usb Devices Driver Download For Windows 10 64-bit
I tried with both serial enum driver and the default option. Rebooting between each attempt. I do not see any new COM device listed when pwoering up the Zedboard. I also ried to in manually and try to force Windows to load the install slabvcp driver for one of the HID USB input devices listed but windows does not allow. I am attaching the. Drivers for the CP2102 have now been installed successfully. I have tested this drivers and installation process in Windows XP, windows 7. Will test is soon on Windows 8 & windows 10. You can see in above image that Port Number 4 has been allocated to this IC. If you want you can even change the virtual com port number from Device Manager.
The older versions of the MD-CC30x-001 USB to SPI and MD-CC40x-001 USB to RS-422/485 communication converter cables were developed to work with Windows 32-bit operating systems. These cables must have the the internal ID reset in order to be supported by current Windows 64-bit operating systems.
How do I know if I have an older cable?
The most recent cable will install as 'Silicon Labs C210x USB to UART Bridge (COMXX)' in the device manager of your PC under Ports (COM and LPT).
In the case of MD-CC3 and MD-CC4 cables with the incompatible ID, when the device manager attempts to find the drivers and fails to install them, the message that opens will show the IMS part number: MD-CC400-000 or MD-CC300-000 on the dialog, as shown below.
Additionally, the part number will display under other devices in your computer's device manager.
Please contact applications for information on cable updates
MD-CC404-000 & MD-CC405-000
The MD-CC404/5-000 drivers are applicable to Lexium MDrive RS-422/485 products. This device is 'plug-n-play' and the drivers should automatically install to an Internet connected PC. Should your network block automated driver installs or the PC not be connected, the drivers may be downloaded from:
MD-CC404-000 Drivers (FTDI VCP Drivers)
Note: This link will open in a new browser tab/window.
MD-CC40x-001
The MD-CC40x-001 drivers are applicable to MDrivePlus and MForce Motion Control RS-422/485 products. This device is 'plug-n-play' and the drivers should automatically install to an Internet connected PC. Should your network block automated driver installs or the PC not be connected, the drivers may be downloaded from:
MD-CC40x-000 Drivers (Silicon Labs CP210x USB to UART Bridge VCP)
Note: This link will open in a new browser tab/window.
Legacy MD-CC40x-001 drivers
Use ONLY with CC4 cables with the IMS ID on 32 bit Windows systems
Driver Package | Installation Instructions
MD-CC30x-001
The MD-CC30x-001 drivers are applicable to MDrivePlus and MForce Step/direction and Speed Control SPI products. This device is 'plug-n-play' and the drivers should automatically install to an Internet connected PC. Should your network block automated driver installs or the PC not be connected, the drivers may be downloaded from:
MD-CC30x-001 Drivers (Silicon Labs CP210x USB to UART Bridge VCP)
Note: This link will open in a new browser tab/window.
Legacy MD-CC30x-001 drivers
Use ONLY with CC3 cables with the IMS ID on 32 bit Windows systems
Rec driver download for windows 10. Driver Package | Installation Instructions
MD-CC50x-000
These drivers apply to the MD-CC500-000 (MDrivePlus and MForce products) and MD-CC501-000 (Lexium MDrive products) USB to CANopen Communications converters
MD-CC50x-000 Drivers (PEAK Systems PCAN-USB)
Note: This link will open in a new browser tab/window.
CP2102 is a USB to UART IC from Silicon Labs. It is my favourite converter IC and I have been using USB to RS232 module and USB to TLL modules based on CP2102 for couple of years without any issues. CP2102 is a cheaper alternative to the costlier ftdi IC (ft232) but cp2102 is a bit difficult to solder as it comes in QFN-28 package and is very small (just 5mmx5mm) in size. The main advantage of CP2102 is that no extra external components are required.
CP2102 IC is used in lot of Arduino UNO Clones, arduino Nano, Node MUC and even in ESP32 Development boards. In this tutorial I will provide you with step by step process to install CP2102 USB Driver in windows.
You can download CP2102 driver from below
- CP2102 USB Driver for Windows XP, 7, 8, 8.1 & Windows 10
Step by Step Installation of CP2102 Drivers
Initially connect your hardware having CP2102 USB to Serial IC to your PC. In the device manager it will show “CP2102 USB to UART Bridge Controller” (as shown in below figure) which means that your PC has detected the drivers but please note the “!” sign which indicated cp2102 drivers have not been installed.
Now extract the “CP210x_Windows_Drivers” in a folder and in that you will find applications named “CP210xVCPInstaller_x64” & “CP210xVCPInstaller_x86”. If your system is 64 bit then run “CP210xVCPInstaller_x64.exe” application and if it is 32 bit then run “CP210xVCPInstaller_x86” application.
Silicon Motion Usb Devices Driver Download For Windows 10 Windows 7
Once you run your application it will show you the welcome screen click “Next” on the screen. Then the license Agreement screen is shown select “I agree” and then on “Next”.
Just relax now the CP2102 drivers will start installing….and within few seconds completed screen will be displayed.
Silicon Motion Usb Devices Driver Download For Windows 10 Offline
Once installed it will show driver successfully installed. Now go again back to device manager and there you will see that the driver has been successfully been installed and a com port has been allotted. In below image you can see that “com4” has been allotted for cp2102 IC in my laptop.
Drivers for the CP2102 have now been installed successfully. I have tested this drivers and installation process in Windows XP, windows 7. Will test is soon on Windows 8 & windows 10.
You can see in above image that Port Number 4 has been allocated to this IC. If you want you can even change the virtual com port number from Device Manager.
For latest CP2102 drivers and for drivers for MAC, Linux and for Android OS please check this link.